Skip to content

Latest commit

 

History

History
126 lines (104 loc) · 9.01 KB

SPEED_TUNING_GUIDE.md

File metadata and controls

126 lines (104 loc) · 9.01 KB

3D Benchy Speed & Quality Tuning Guide — Bambu Lab P2S

Target Printer: Bambu Lab P2S (0.4 mm Hardened Steel Nozzle)
Slicer: Bambu Studio / OrcaSlicer
Filaments Covered: UJOYBIO Elite PLA+, Kingroon PLA Basic, Kingroon PLA Matte, Inslogic Tri-Color Silk PLA, Kingroon Silk PLA.
Purpose: Progressive speed calibration matrix with interactive test logging columns for post-print evaluation, failure diagnosis, and permanent profile optimization.


1. Physical Speed Governors & Safety Rules

Before increasing speeds, keep these 3 inviolable rules in mind:

  1. Never Touch the First Layer: Keep Initial Layer Speed at 50 mm/s, Infill at 105 mm/s, Bed at 60 °C, and Fan OFF for layers 1–3.
  2. Initial Layer Nozzle Temp (Prime Line Snap): Set Initial Layer Nozzle Temp to 202 – 205 °C (even if other layers run at 215 – 220 °C). This prevents the prime line from dragging an elastic ooze string across the plate.
  3. The Volumetric Flow Ceiling ($V_{max}$): $$\text{Actual Linear Speed (mm/s)} = \min\left(\text{Target Speed}, \frac{V_{max}}{\text{Layer Height} \times \text{Line Width}}\right)$$ If $V_{max} = 15\text{ mm}^3/\text{s}$, at 0.20 mm height and 0.42 mm width, your maximum physical speed is 178.5 mm/s. To print infill at 270 mm/s, you must ensure $V_{max} \ge 23\text{ mm}^3/\text{s}$ and increase nozzle temperature so the hotend can melt plastic fast enough.

2. Progressive Benchy Speed-Tuning Matrix (With Test Note Columns)

Use this table to record settings and results as you dial in your printer.

Tuning Parameter Stage 1: Quality Baseline (Precision) Stage 2: Balanced Sport (Fast Functional) Stage 3: Ludicrous (Max Flow Limit) Test 1 Notes & Settings Test 2 Notes & Settings Test 3 Notes & Settings Final Dialed-In Profile
Layer Height 0.08 mm / 0.12 mm / 0.16 mm 0.20 mm / 0.24 mm 0.24 mm / 0.28 mm
Initial Layer Height 0.20 mm 0.20 mm 0.20 mm / 0.24 mm
Outer Wall Speed 60 mm/s (Silk: 40 mm/s) 90 – 100 mm/s (Silk: 50 mm/s) 120 – 140 mm/s (Silk: N/A)
Inner Wall Speed 120 mm/s 180 – 200 mm/s 240 – 260 mm/s
Sparse Infill Speed 180 mm/s 250 – 270 mm/s 300 – 330 mm/s
Internal Solid Infill 150 mm/s 200 – 220 mm/s 250 – 270 mm/s
Top Surface Speed 70 – 80 mm/s 90 – 100 mm/s 120 mm/s
Outer Wall Accel 2,000 mm/s² 3,000 mm/s² 4,000 mm/s²
Normal Accel 5,000 mm/s² 8,000 mm/s² 10,000 mm/s²
Nozzle Temp (1st Layer) 202 – 205 °C 204 – 206 °C 208 – 210 °C
Nozzle Temp (Other Layers) 204 – 208 °C 215 – 218 °C 222 – 228 °C
Bed Temp (1st / Others) 60 °C / 55 °C 60 °C / 55 °C 60 °C / 55 °C
Max Volumetric Speed ($V_{max}$) 12 – 14 mm³/s 16 – 18 mm³/s 20 – 24 mm³/s
Observed Benchy Print Time ~28 – 35 min ~18 – 22 min ~13 – 16 min
Surface Finish (Gloss/Matte) Glossy / Uniform Smooth satin Matte patches / Ringing?
Bow Overhang (60° Quality) Perfect, no sag Clean, minor texture Sagging or curling?
Cabin Ceiling Bridge Zero droop Flat, 1–2 loose strands Drooping or gaps?
Stern Text Legibility Sharp, crisp Readable Smudged or blurred?
Chimney & Mast Rigidity Strong, solid Strong Delamination or brittle?
Prime Line Whisker Result Clean snap (no hair) Clean snap Clean snap

3. Dedicated Process Profile Matrix (Installed in Bambu Studio)

You can select any of the 30 custom-calibrated process profiles directly from Bambu Studio's Process dropdown. They follow the naming pattern: "<layer_height> <Brand> <Type> @BBL P2S"

Layer Height UjoyBio PLA Plus Kingroon PLA Basic Kingroon PLA Matte Inslogic Tri-Color Silk Kingroon Silk PLA
0.08 mm 0.08mm UjoyBio PLA Plus @BBL P2S 0.08mm Kingroon PLA Basic @BBL P2S 0.08mm Kingroon PLA Matte @BBL P2S 0.08mm Inslogic Tri-Color Silk PLA @BBL P2S 0.08mm Kingroon Silk PLA @BBL P2S
0.12 mm 0.12mm UjoyBio PLA Plus @BBL P2S 0.12mm Kingroon PLA Basic @BBL P2S 0.12mm Kingroon PLA Matte @BBL P2S 0.12mm Inslogic Tri-Color Silk PLA @BBL P2S 0.12mm Kingroon Silk PLA @BBL P2S
0.16 mm 0.16mm UjoyBio PLA Plus @BBL P2S 0.16mm Kingroon PLA Basic @BBL P2S 0.16mm Kingroon PLA Matte @BBL P2S 0.16mm Inslogic Tri-Color Silk PLA @BBL P2S 0.16mm Kingroon Silk PLA @BBL P2S
0.20 mm 0.20mm UjoyBio PLA Plus @BBL P2S 0.20mm Kingroon PLA Basic @BBL P2S 0.20mm Kingroon PLA Matte @BBL P2S 0.20mm Inslogic Tri-Color Silk PLA @BBL P2S 0.20mm Kingroon Silk PLA @BBL P2S
0.24 mm 0.24mm UjoyBio PLA Plus @BBL P2S 0.24mm Kingroon PLA Basic @BBL P2S 0.24mm Kingroon PLA Matte @BBL P2S 0.24mm Inslogic Tri-Color Silk PLA @BBL P2S 0.24mm Kingroon Silk PLA @BBL P2S
0.28 mm 0.28mm UjoyBio PLA Plus @BBL P2S 0.28mm Kingroon PLA Basic @BBL P2S 0.28mm Kingroon PLA Matte @BBL P2S 0.28mm Inslogic Tri-Color Silk PLA @BBL P2S 0.28mm Kingroon Silk PLA @BBL P2S

4. Filament-Specific Master Reference Cards

Card A: UJOYBIO Elite PLA+ (Hyper PLA+ / Toughened Pro)

  • Optimal Flow Sweet Spot: 16 – 18 mm³/s
  • Characteristics: High impact resistance, smooth layer blending, fast melting.
  • Speed Recommendation:
    • 0.16 mm Precision: Outer wall 60 mm/s, Infill 180 mm/s, Temp 205 °C (prevents oozing/stringing).
    • 0.20 mm Standard: Outer wall 80 mm/s, Infill 250 mm/s, Temp 212 °C.
    • 0.24 mm Speed: Outer wall 100 mm/s, Infill 270 mm/s, Temp 218 °C.
    • 0.28 mm Extra Draft: Outer wall 110 mm/s, Infill 220 mm/s, Temp 220 °C.

Card B: Kingroon PLA Basic

  • Optimal Flow Sweet Spot: 14 – 16 mm³/s
  • Characteristics: Standard reliable rapid prototyping PLA.
  • Speed Recommendation:
    • Outer wall: 80 – 100 mm/s
    • Infill: 220 – 250 mm/s
    • Nozzle temp: 210 – 220 °C
    • Bed temp: 60 °C / 55 °C

Card C: Kingroon PLA Matte

  • Optimal Flow Sweet Spot: 12 – 14 mm³/s
  • Characteristics: Matte additives hide layer lines naturally, but have lower interlayer shear strength.
  • Speed Recommendation:
    • Do not exceed 14 mm³/s flow.
    • Outer wall: 70 – 80 mm/s
    • Infill: 180 – 200 mm/s
    • Nozzle temp: 210 – 215 °C

Card D: Inslogic Tri-Color Silk PLA

  • Optimal Flow Sweet Spot: 10 – 12 mm³/s (for mirror sheen), 14 mm³/s (structural)
  • The Silk Golden Rule: Speed dictates reflectivity. Faster printing cools into a dull matte plastic; slow printing yields deep metallic luster.
  • Speed Recommendation:
    • Outer Wall: Strictly 40 – 50 mm/s across ALL layer heights.
    • Inner Wall: 120 – 150 mm/s
    • Infill: 180 – 200 mm/s
    • Nozzle Temp: 215 – 225 °C (higher temp keeps luster during internal high speeds).
    • Bed Temp: 55 – 60 °C

Card E: Kingroon Silk PLA

  • Optimal Flow Sweet Spot: 10 – 12 mm³/s
  • Speed Recommendation:
    • Outer Wall: Strictly 35 – 45 mm/s
    • Inner Wall: 100 – 120 mm/s
    • Infill: 160 – 180 mm/s
    • Nozzle Temp: 212 – 220 °C
    • Bed Temp: 55 – 60 °C

4. Benchy Diagnostic Defect & Correction Cheat Sheet

Symptom on Benchy Root Cause Immediate Slicer Fix
Ghosting / Ringing Waves on hull near anchor hole Excessive outer wall acceleration vibrating toolhead Reduce Outer Wall Acceleration from 4,000 to 2,500 – 3,000 mm/s².
Loose Sagging Strands under cabin roof bridge Bridge speed too fast or cooling inadequate Set Bridge Speed to 25 – 30 mm/s and ensure Auxiliary/Part Fan is 100%.
Curling / Upturned Edges on bow overhang ($60^\circ$) Plastic staying molten too long on shallow overhang Under Speed -> Overhang Speed: set $50-75%$ overhangs to 30 mm/s and $75-100%$ to 15 mm/s.
Prime Line Whisker stretching to model brim High nozzle temp causing ooze during initial travel Set Initial Layer Nozzle Temp to 202 – 205 °C (keep other layers at 215 °C).
Extruder Clicking / Under-extrusion during infill Volumetric flow limit exceeded by linear speed demand Increase nozzle temp by 5 °C OR reduce Infill Speed by 30 mm/s OR reduce $V_{max}$ to 16 mm³/s.
Silk Filament Turning Dull / Chalky Printing outer wall too fast Lock Outer Wall Speed to 40 – 50 mm/s.
Brittle Layers / Snapping at Z seam Inadequate melt fusion at high speed Raise nozzle temperature by 5 – 8 °C.